palm pre 1.3.5.1 内存扫描结果

23:46:19 : Couldn’t open port COM1
23:46:52 : Scanning flash for readable data. Step – 1024 bytes
23:46:52 : READABLE area at 0x00000000
23:46:55 : Unreadable area at 0x00001000
1:34:52 : READABLE area at 0x001FB400
1:34:55 : Unreadable area at 0x001FE000
1:35:17 : READABLE area at 0x00200000
1:35:21 : Unreadable area at 0x00201000
1:35:30 : READABLE area at 0x00202000
1:35:32 : Unreadable area at 0x002A4C00
1:35:32 : READABLE area at 0x002A5000
1:35:55 : Unreadable area at 0x00944000
1:36:05 : READABLE area at 0x00945000
1:36:07 : Unreadable area at 0x009EA000
1:36:07 : READABLE area at 0x009EA400
1:36:37 : Unreadable area at 0x012F7000
10:29:21 : User break at address 0x01CB9400
10:29:21 : Scan completed

Advertisements

Sprint PST Settings with Boost Provisioning

NAM Name: SPCS
SCM: 42
Software Version: 3.56.651.0 -varies
Firmware Version: 3.42.02 -varies
Hardware Version: 0003
PRI Version: 2.04_003 -varies
PRI Checksum: 449def22 -varies

(NAM Settings)
NAM Name: SPCS
MDN:
MIN1:
MIN2:
MSID:
MCC: 310
MNC: 00
NMSI: 00
IMSI: 31000
True MIN1:
True MIN2:
True IMSI_S:
True MCC: 000
True MNC: 00
True NMSI: 00
True IMSI: 00000
ACCOLC: 4

(CDMA Settings)
A-Sys Primary: 283
B-Sys Primary: 384
A-Sys Secondary: 691
B-Sys Secondary: 777
MOB_TERM_FOR_HOME: Enable
MOB_TERM_FOR_SID: Enable
MOB_TERM_FOR_NID: Enable
EVRC Enabled: Enable
Home Page: EVRC
Home Orig: EVRC
Roam Orig: Voice 13K

(Home SID/Home NID)
All settings are 0 / 0

(Modem Settings)
Slot Cycle Index: 2
Preferred Serving System: Sprint Only
Preferred Mode: Automatic
HDR Hybrid Preferred: Enable
Clear all MRU entry: No

(Data Parameters)
Packet Dial String: #777
Rev.A: Enable -varies (Model Specific)

(M.IP Settings)
Number of Profiles: 2
Active User Profile Index: 1
MIP_MODE: Mobile IP Only
MIP Registration Retries: 1
MIP Registration Retry Timeout: 2000 ms
MIP Pre-Registration Timeout: 30
Mobile Node-HA Authentication: Disable
Send a Registration Request Only: Enable
Dormant Handoff Optimization: Disable

(MID Default Profile)
Enable Profile: Enable
NAI: @hcm.sprintpcs.com
MN HA SPI Set: Enable
MN HA SPI Value(Hex): 4D2
MN AAA SPI Set: Enable
MN AAA SPI Value(Hex): 4D2
Reverse Tunneling Preference: Enable
Home Address: 0.0.0.0
Primary HA Address: 68.28.15.12
Secondary HA Address: 68.28.31.12
DMU Public Key: 0

(M.IP Customer Profile 1)
Enable Profile: Enable
NAI: @myboostmobile.sprintpcs.com -varies (Boost Account)
MN HA SPI Set: Enable
MN HA SPI Value(Hex): 4D2
MN AAA SPI Set: Enable
MN AAA SPI Value(Hex): 4D2
Reverse Tunneling Preference: Enable
Home Address: 0.0.0.0
Primary HA Address: 255.255.255.255
Secondary HA Address: 68.28.89.76
DMU Public Key: 0

HTC Hero MEID change

Default Sprint Hero – MEID Solutions
1. Get SPC

HOW TO READ / RESET SPC = SuperSPC Method

Start CDMA Workshop and Connect the Phone go to Terminal Tab (Second Tab) type 41 74 64 77 61 6F 70 inside it and click to Send for 2 or 3 times, then immediately go to Security Tab and Click to read SPC, again Send that SPC and then Zero it and rewrite. then just go to security and read/write your new spc

2. Zero all pESN and MEID

Install QxDM Connect to Proper Port and Open View – New – Memory Viewer

pESN addresses:

0x015ADA85
0x015ADB53
0x015AF5C5
0x015AF58F
0x015AF693
0x1876CB80
0x18774744
0x187764CC
0x18858DE8
0x188BF514
0x188BF5EC
0x188C5C18
0x188CEB58
0x188D13F0
0x188D6760
0x18D4133D

MEID address

0x0142201C
0x01422028
0x015B46DC
0x1876A658
0x18771248
0x187759D0
0x188BF9AC
0x189AAAEC
0x189AABBC
0x189B7CF0

Enter above Address and Press Enter if you find ESN or MEID in Reverse order Just Zero 8 Numbers / or 14 Number for MEID and Click to write

3. Now in QxDM in View Menu Select (Command Bar, Status Bar, View Bar)

now in Command bar
Enter the Following Commands

RequestNVItemWrite esn 0x0
RequestNVItemRead meid
RequestNVItemWrite meid 0x0000000000000000

It must say MEID and ESN as Zeroes. if its Zeroed Reboot it and move to Next Step or try again to Find Locations and Zero it.

4. Final Step Try to Issue the Following Command

RequestNVItemWrite meid 0x00a1000001234abc (Actual MEID)
RequestNVItemRead meid
RequestNVItemRead esn

if it fails Reboot your Phone then go to Settings – About – Status and Check that MEID = 0000000000000 and ESN = 00000000
if yes do Final Step Once again

How to Convert Hero to ESN only – Remove MEID

Once you Zero all MEID and ESN and reboot it in CDMA Workshop it if shows SCM (Station Class Mask) = 2A (2A = ESN Based 3A = MEID Based )

Now Read ESN from NV Method, if ESN Show Zero Reboot it and try to Write new ESN using NV Method (CDMA Workshop or QxDM) it must says Success. or else Reboot and try

PLEASE SAY THANKS and also thanks the following people and all Thread members

Salutes to My Heroes – shadowmite, zaquaz, supadoggie, the_miker, tonycortes
Attached Files
File Type: rar android_usb_drivers_x32_x64_sdk1.6-r1.rar (6.08 MB, 380 views)
File Type: rar HTC_Hero_DIAG_Drivers.rar (1.10 MB, 325 views)

0x0142201C – MEID
0x01422028 – MEID
0x015AF59E – pESN
0x015B46DC – MEID
0x1876A658 – MEID
0x1876CB80 – pESN
0x18771248 – MEID
0x187759D0 – MEID
0x18774744 – pESN
0x187764CC – pESN
0x18858DE8 – pESN
0x188BF9AC – MEID
0x188BF514 – pESN
0x188C5C18 – pESN
0x189AAAEC – MEID
0x189AABBC – MEID
0x189B7CF0 – MEID
0x18D4133D – MEID
0x015af5c5 – pESN